Adding the RXU Chain and RF Module (Star Topology)

This describes how to add the RXU chain and RF module when the BBU and the RF module are connected in star topology.

Prerequisite

The following procedure takes how to configure the RXU chains and GRFUs of BTSs in S2/2/2 mode as an example. The configuration result is shown in Figure 1.

Figure 1 Configuration result of the star topology

NOTE:

• Each GTMU supports a maximum of six RXU chains.
• When star and chain topologies are applied for the BBU and the RF module, each chain supports three-level cascading of the RF module.
• With different settings of Cabinet Mapping Rule, both the location of the DRFU/GRFU/MRFU and the value of Hop set for the RXU chain are different. For details, see Mapping Rule of the RFU Cabinet.
• According to the cabinet mapping rule, Mapping Rule for Two Cabinets should be configured for the two-level cascading of the RXU chain.
• According to the cabinet mapping rule, Mapping Rule for Three Cabinets should be configured for the three-level cascading of the RXU chain.

Procedure

1. In the Site Device Attributes dialog box, right-click the corresponding slot as described in Figure 2, and choose Add Board > GRFU. A shortcut menu is displayed, as shown in Figure 3.
   Figure 2 Site Device Attributes dialog box
   
   
   Figure 3 Configure Chain of Board dialog box
   
   

2. Set RXU NAME, SFP Port No., and Hop. Click OK. The GRFU is added.
   CAUTION:

   SFP Port No. must be consistent with the CPRI ports connected to the GTMU.

   Hop indicates the grade of the RXU chain that is carried on the board.

3. Right-click the GRRU and then choose Configure RXU Attribute from the shortcut menu. In the displayed dialog box, click the Configure Site Board Attributes tab to set related parameters, as shown in Figure 4.
   Figure 4 Basic Attributes of Site Board dialog box
   
   
   NOTE:

   • When the DRRU is applied, Associated DRRU Board No. is displayed in the dialog box.
   • When the GRRU or MRRU is applied, Associated RXU Board No. is displayed in the dialog box.
   • When the DRFU is applied, Associated DRFU Board No. is displayed in the dialog box.
   • When the GRFU or MRFU is applied, Associated RXU Board No. is displayed in the dialog box. In addition, Support Diversity Transmitter or Four Diversity Receiver is added.

4. Set the parameters by referring to Table 2.

   Table 2 Description of setting board attributes of the BTS

   Parameter	Setting Description
   Send Receive Mode	Set this parameter according to the actual RF connections. For details, see Setting Antenna Attributes. The DRRU, GRRU, and MRRU support the following TX/RX modes: Single Feeder (1TX + 1RX), Single Feeder (1TX + 2RX), Double Feeder (2TX + 2RX), Double Feeder (2TX + 4RX), Double Feeder (1TX + 1RX), and Double Feeder (1TX + 2RX). The DRFU supports the following TX/RX modes: Single Feeder (1TX + 1RX), Single Feeder (1TX + 2RX), Double Feeder (2TX + 2RX), Double Feeder (2TX + 4RX), Double Feeder (1TX + 1RX), and Double Feeder (1TX + 2RX). The GRFU and MRFU support the following TX/RX modes: Single Feeder (1TX + 1RX), Single Feeder (1TX + 2RX), Double Feeder (2TX + 2RX), Double Feeder (2TX + 4RX), Double Feeder (1TX + 1RX), and Double Feeder (1TX + 2RX).
   Support Diversity Transmitter or Four Diversity Receiver	When the GRFU or MRFU is added, this parameter is displayed. When Send Receive Mode of the GRFU or MRFU is set to Double Feeder (2TX + 4RX), Associated RXU Board No. can be configured only when you set this parameter to Yes.
   Associated DRRU Board No. or Associated RXU Board No.	You need to set this parameter when Send Receive Mode of the DRRU is set to Single Feeder (1TX + 2RX) or Double Feeder (2TX + 4RX). You need to set this parameter when Send Receive Mode of the MRRU and the GRRU is set to Double Feeder (2TX + 4RX). You need to set this parameter when Send Receive Mode of the GRFU and the MRFU is set to Double Feeder (2TX + 4RX). The value of this parameter must be consistent with that set in the "Basic Attributes of Site Board" dialog box for the corresponding board.
   Antenna Tributary 1 Tower-Top Amplifier Flag and Antenna Tributary 2 Tower-Top Amplifier Flag	Set this parameter according to the actual configuration of the antenna.
   Antenna Tributary 1 Tower-Top Amplifier Attenuation Factor(dB) and Antenna Tributary 2 Tower-Top Amplifier Attenuation Factor(dB)	Set this parameter to TMA Gain-4. Obtain information on the "TMA gain" from the product specifications.

   NOTE:

   • You need not set Associated DRFU Board No. in any TX/RX mode.
   • The prerequisite for configuration of Associated DRRU Board No. or Associated RXU Board No. is that the associated RF module is configured and the RF module does not have any association with other boards.

5. Click OK to return to the Site Device Attributes dialog box.
6. Right-click the GRFU, and then choose Bind Logical TRX from the shortcut menu. A dialog box is displayed, as shown in Figure 5.
   Figure 5 Binding logical TRX dialog box
   
   
   NOTE:

   • Different logical TRXs on the same board can be configured to different cells.
   • If the DRRU, DRFU, GRFU, or MRFU is added, you need not select transmit channel A or B in the Binding logical TRX dialog box.

7. Select the required TRXs and the cells allocated to them, and set TRX numbers.
8. Click OK to return to the Site Device Attributes dialog box.
9. Repeat 1 through 8 to configure other RXU chains and RF modules.
10. On the right side of the Site Device Attributes dialog box, set RFU view type to View by topology. The result of the configuration in star topology is shown in Figure 6.
    Figure 6 Site Device Attributes dialog box