X400: How to Create a LoopBack Message

Last reviewed: October 20, 1997
Article ID: Q135030
3.00 3.20 MS-DOS kb3rdparty

The information in this article applies to:

  • Microsoft Mail Gateway to X.400, versions 3.0 and 3.2

SUMMARY

This article explains how to create a LoopBack message for troubleshooting the X.400 Mail Gateway.

MORE INFORMATION

  1. Type the following:

          x400adm  admin -ppassword -d<drive letter to gateway po>
    

  2. Select the Local MTA option, and get the following information:

          - Name:
          - Country Code:
          - Admd Name:
          - Prmd Name:
    

    Click OK (ALT+O) to accept the changes, and go back to previous screen.

  3. Select the Address Conversion option.

    The administrator must specify one address conversion string for each network name. One network address conversion string covers all postoffices with the same network name, even if they are not on the same local area network.

          - In the Network field, type the name of the Microsoft Mail network.
          - Set the Org Name to %net by tabbing to the field, then press ALT+N.
          - Set the Org Unit 1 to %post by tabbing to the field, then press
    
            ALT+P.
          - Set the Surname to %mbx by tabbing to the field, then press ALT+M.
          - Select Add (ALT+A).
          - Select OK (ALT+O) to return to the previous screen.
    
    

  4. Select the Routing option. The routing table will look similar to the following:

    NOTE: The syntax is very important. The dots ".." must exist.

         c = country code <item b from Step 1>
         ..a = Admd Name <item c from Step 1>
         ....p = Prmd Name <item d from Step 1>
         ......o = Org Name <item g from Step 2> <Local MTA Name: Item 1>
    

  5. After you complete the above steps, run the MS-DOS Mail client. Login as the Admin to the postoffice, and select Address, X400, Field. This will display the Field template.

    In the Field template, enter the following:

          - Country Code:                  <item b from Step 1>
          - Administration Domain name:    <item c from Step 1>
          - Private Domain Name:           <item d from Step 1>
          - Surname:                       <your mailbox name>
          - Organization name:             <Network name of the postoffice>
          - Organization Unit Names (OU):  <postoffice name>
    
       Press <Enter>
       At the Alias field, type in LoopBack Account <Account Name>
    
    

  6. The address is put into your Personal Address List (PAL). Press the ESC key until the Compose option appears.

  7. Compose a message using the account above, and run the X400Gate program with the following command line options:

          X400gate -lvd -d< drive letter to PO >
    

    If the message is delivered, the X400Gateway should be configured correctly. If there are error messages in the MAILDATA\LOG\X400xxxx.LOG file, follow the troubleshooting steps to resolve the appropriate error message.

    NOTE: The xxxxx in the LOG file represents the date you run the gateway file. For example, if you run X400GATE.EXE on July 27, the filename would be X4000727.LOG.

More information about the X400 gateway can be found in the Microsoft Mail Gateway to X.400 "Administrator Guide."


Additional reference words: 3.00 3.20
KBCategory: kb3rdparty
KBSubcategory: MailGWX400


THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

Last reviewed: October 20, 1997
© 1998 Microsoft Corporation. All rights reserved. Terms of Use.