How to Determine When Another Application Has Finished

Last reviewed: July 22, 1997
Article ID: Q67673
3.00 3.10 WINDOWS kbprg

The information in this article applies to:

  • Microsoft Windows Software Development Kit (SDK) for Windows versions 3.0 and 3.1

SUMMARY

Two separate applications sometimes need to cooperate in the Windows environment. Two Windows-based applications may work in tandem, or a Windows-based application may require the services of a an application that is not based on Windows.

This article examines the issues involved when a Windows-based application requires notification that another application has completed processing.

MORE INFORMATION

First, the following constraints should be considered:

  1. Windows was not designed to synchronize the operation of a Windows-based application with an MS-DOS-based application in any mode (real, standard, or 386 enhanced).

  2. Windows does not provide any automatic way to determine if another application finished, or ran correctly.

This first section included below discusses techniques that can be included in code that is written for cooperating applications (for example, when both are Windows-based applications and when one is for Windows and the other is not). The second section listed below discusses techniques to apply when the other application is beyond the programmer's direct influence.

Techniques to Use for Cooperating Applications

The following are two options that can be used if the programmer is developing both applications and each runs under Windows:

  1. The two applications can communicate through a dynamic data exchange (DDE) messaging protocol that the programmer establishes.

  2. Each application can register the same application-specific message text with Windows via the RegisterWindowMessage() function and receive a numeric value for the message. The terminating application then sends this value to the other application. This can be accomplished by broadcasting the message to all windows in the system. See the documentation for PostMessage().

When one of the cooperating applications that is being developed does not run under Windows, the following must occur:

  1. When the MS-DOS-based application completes or encounters a fatal error, it should write a message into a specified file in the TEMP directory.

  2. The Windows-based application should then perform the following steps:

    a. Use the SetTimer() function to create a system timer that will

          fire at desired intervals. The estimated completion time of the
          function is one possible interval. Another would be "estimated
          time to first possible failure" if the MS-DOS-based application will
          be writing an error string for the Windows-based application to
          display.
    

    b. Initiate the execution of the MS-DOS-based application with the

          WinExec() function and continue with any normal processing.
    

    c. Upon receipt of the timer message, the TEMP directory can be

          checked to determine if a message file is present. If the file
          is present, the message in the file is parsed to see if
          termination was due to success or failure.
    

Techniques to Use for Third-Party Applications

For a third-party application, the steps taken must access information that is entirely external to the MS-DOS-based application. One possible way to implement this method is to use the title of the WINOLDAP window to determine if the application is still running. In this case, the following steps should be taken:

  1. Use the SetTimer() function to create a system timer. Timer messages should be at least a few seconds apart. This allows WINOLDAP to create its window and begin processing.

  2. In real and standard modes, Windows-based application processing stops while the MS-DOS-based application is processing. In enhanced mode, Windows' behavior depends on the settings in the program information file (PIF) that corresponds with the MS-DOS application. For more information about the allocation of the processor when an MS-DOS-based application is running, query on the following keywords:

    prod(winsdk) and WinExec() and dependent

  3. When the timer message is received, the FindWindow() function is then used to search for the caption of the MS-DOS-based application's window. The caption is created from the "Window Title" section of its PIF file, or if it is blank or not found, the filename of the old application. If the caption is no longer present, the application is deemed to have completed its processing.

Another possible solution is to create a batch file in MS-DOS that checks for error level information returned from the program, and then creates files in the TEMP directory. The Windows-based application can then check for these "result" files to determine the MS-DOS-based application's status.

The following batch file creates a sentinel file named BEGIN.TMP. Until this file is deleted, the MS-DOS-based application is considered to be running. Successful completion creates the result file, END.TMP, and then BEGIN.TMP is deleted. An execution error creates the result file named STOP.TMP, and then removes BEGIN.TMP.

     1:  echo start > %TEMP%\begin.tmp
     2:  MyDosApp
     3:  if errorlevel 1 goto bad
     4:  if errorlevel 0 goto good
     5:  goto end
     6:  :bad
     7:  echo bad > %TEMP%\stop.tmp
     9:  goto end
     10: :good
     11: echo good > %TEMP%\end.tmp
     12: goto end
     13: :end
     14: del begin.tmp
     15: goto end

A system timer is employed as above to direct the Windows-based application to check for the existence of the sentinel and result files.


Additional reference words: 3.00 3.10
KBCategory: kbprg
KBSubcategory: KrTsksIns
Keywords : kb16bitonly


THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

Last reviewed: July 22, 1997
© 1998 Microsoft Corporation. All rights reserved. Terms of Use.