Running PC-NFS 5.0 with Windows for Workgroups

Last reviewed: November 21, 1994
Article ID: Q101177
The information in this article applies to:
  • Microsoft Windows for Workgroups version 3.1

SUMMARY

Sun Microsystems has announced that version 5.0 of its PC-NFS network operating system software supports connectivity with Microsoft Windows for Workgroups (WFWG) version 3.1. This article describes how to set up PC-NFS with Windows for Workgroups. This procedure is designed for use with PC-NFS version 5.0 only; previous versions of PC-NFS are not compatible with Windows for Workgroups.

Microsoft will assist in the installation of PC-NFS with Windows for Workgroups. Sun Microsystems is responsible for supporting the installation, configuration, and use of PC-NFS. Customers who have issues that cannot be resolved with standard network troubleshooting should contact Sun Microsystems for assistance.

MORE INFORMATION

Installing WFWG and PC-NFS Version 5.0

To use PC-NFS version 5.0 with Windows for Workgroups version 3.1, you must use the updated WFWNET.DRV driver included with PC-NFS. To update the driver, simply delete the current version located in your WINDOWS\SYSTEM subdirectory, and replace it with the current version.

To install and provide connectivity to PC-NFS and Windows for Workgroups, do the following:

  1. Install Windows for Workgroups version 3.1.

  2. Run the PC-NFS Install program, and select NDIS as the network adapter.

  3. Run the QuickNDIS utility, and configure it for Windows for Workgroups.

  4. Run the Winstall program.

NOTE: For further information about installing and configuring PC-NFS, refer to your PC-NFS documentation.

The installation program for Sun PC-NFS makes changes to the AUTOEXEC.BAT, CONFIG.SYS, PROTOCOL.INI, and SYSTEM.INI files. These changes are documented in your PC-NFS installation guide.

AUTOEXEC.BAT

The following lines are added to the AUTOEXEC.BAT file, but the SET statements vary with each installation:

   Set TZ=EST5EDT
   Set NFSDRIVE=C
   Set NFSPATH=C:\NFS
   Set TN_DIR=C:\NFS\TELNET
   C:\NFS\PRT *
   C:\NFS\NET INIT
   C:\NFS\RTM

CONFIG.SYS

The following lines are added to the CONFIG.SYS file after the device drivers installed by Windows for Workgroups. The lines should appear in this order:

   Device=C:\NFS-NDIS.SYS
   Device=C:\NFS\PCNFS.SYS
   Device=C:\NFS\SOCKDRV.SYS

PROTOCOL.INI

The following section is added to the PROTOCOL.INI file:

   [NFS-NDIS]
   DriverName=NFSLINK$
   Bindings=MS$ELNKII


SYSTEM.INI

The following lines are added to the identified sections of the SYSTEM.INI file:

   [Boot]
   secondnet.drv=pcnfs.drv

   [386Enh]
   secondnet=pcnfs.386

WFWG and Previous Versions of PC-NFS

If you install Windows for Workgroups version 3.1 on a network running a version of PC-NFS earlier than version 5.0, Windows for Workgroups does not display a warning that this version of PC-NFS is not supported. (Normally, Windows for Workgroups issues a warning during setup if the currently installed networking software is not compatible with Windows for Workgroups.)

Windows for Workgroups version 3.1 Setup does not have the ability to detect the presence of a PC-NFS network.

To run Windows for Workgroups properly on a Sun PC-NFS workstation, you must either update your PC-NFS software to version 5.0 or remove all references to PC-NFS connectivity from the CONFIG.SYS and AUTOEXEC.BAT files. If you don't remove the references to the Sun client software before rebooting, the system may stop responding (hang) as the conflicting network device drivers attempt to load.

The products included here are manufactured by Sun Microsystems, a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability.


KBCategory: kbnetwork kbdisplay kb3rdparty kbsetup
KBSubcategory: wfw wfwg
Additional reference words: 3.10 3.1


THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

Last reviewed: November 21, 1994
© 1998 Microsoft Corporation. All rights reserved. Terms of Use.