WinNT Support for Compaq Smartdesk 2855 cnt75MB21 Docking Statio

Last reviewed: March 19, 1998
Article ID: Q163110
The information in this article applies to:
  • Microsoft Windows NT Workstation versions 3.5 and 3.51
  • Microsoft Windows NT Server versions 3.5 and 3.51

SUMMARY

The Compaq Smartdesk 2855 cnt75MB21 has a built-in Netflex-2 network card based on the Intel 595 chipset. This network card is not inherently supported by Windows NT and requires a device driver from Compaq.

Currently, there is no driver support available for Windows NT version 4.0.

The Compaq driver is contained in a Softpaq file called Sp1251.exe and can be found on Compaq’s Web site.

The Network adapter must be pre-configured using the flashset or softset2 diagnostic disk that shipped with your laptop or docking station.

The network adapter can only be configured for IRQ-11, unless a newer version diagnostic utility disk is used, contact Compaq Support for more detail.

The Compaq Smartdesk 2855 cnt75MB21 also contains a built-in SCSI controller, make sure the SCSI controller is configured to use a different IRQ other than IRQ-11 prior to loading the NIC device driver.

The SCSI controller is based on the Adaptec 151x/152x/AIC 6260/6360 and can use the supported device driver Sparrow.sys that ships with Windows NT by using Windows NT Setup\options\add remove SCSI adapter.

For more information regarding this controller, please see the following Microsoft Knowledge Base article:

   ARTICLE-ID: Q102651
   TITLE     : Required Settings for Adaptec 1510 SCSI Host Adapter

MORE INFORMATION

The following are excerpts from the Readme.txt contained on the Compaq Softpaq Sp1251.exe for network card support.

  1. The NIC adapter should be configured prior to setting it up in NT.

  2. In NT, select the Control Panel choose the Network icon select "Add Adapter".

  3. A list of available adapters will be displayed. Choose "Other <Requires> disk from manufacturer".

  4. Insert the Compaq Integrated NetFlex-2 ENET Drivers disk and press enter.

  5. A dialog box will come up with "A:\-". Change the path "A:\NT\35" which is the path where the driver EPRONT.SYS and setup file OEMSETUP.INF are located.

  6. The screen will come up with four settings: Interrupt; I/O Port; I/O Channel Ready; and Transceiver Type. Make sure the values that come up match the actual board settings as configured with FlashSet or SoftSet2. DO NOT change the I/O Channel Ready. The proper setting was already determined. Changing this parameter could cause the adapter to become inoperable. Click on OK to accept the adapter settings. Click on OK to exit the network configuration screen.

  7. NT will then perform the binding process. If any additional network software options were installed, you may be prompted for specific information for these packages.

  8. Restart NT when prompted, in order for the changes to take affect.


Additional query words: ProLinea Net1/25s ProLinea Net1/33s
Keywords : ntdriver NTSrvWkst kb3rdparty
Version : WinNT:3.5,3.51
Platform : winnt


THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

Last reviewed: March 19, 1998
© 1998 Microsoft Corporation. All rights reserved. Terms of Use.