WinNT Err: DHCP Specified Range Overlaps Or Already Exists

Last reviewed: January 13, 1998
Article ID: Q164330
The information in this article applies to:
  • Microsoft Windows NT Server versions 3.5, 3.51, and 4.0

SYMPTOMS

When you create a new DHCP scope, one of the following error messages may be displayed:

   The specified range either overlaps with an already existing
   range or is invalid.

   The specified subnet already exists.

CAUSE

One possible cause is documented in the Microsoft Knowledge Base article:

   ARTICLE-ID: Q129122
   TITLE     : DHCP: Excluding an Address Before Lease Expires Gives Error

However, if this is a brand new scope, it is more likely that the scope is subnetted, and the Start Address and End Address overlap two or more subnets.

For example, an Internet Service Provider (ISP) provides a scope of addresses for a customer, from 205.241.139.160 to 205.241.139.223 and a subnet mask of 255.255.255.160. Trying to create a single scope with this starting/ending range, and using the supplied subnet mask prompts the user with the error message shown above.

DHCP Manager performs a calculation on the information the user supplies and detects that the ranges of addresses do not all exist within the same subnet. The user can verify this themselves by performing an AND-ing operation against the Start Address and the Subnet Mask and also against the End Address and the Subnet Mask. Then, the user can compare the two resulting values, if they do not match, then the starting and ending addresses are not part of the same subnet.

   NOTE: AND-ing is the process of comparing 2 bits (in this case, each
   bit of the IP address and subnet mask). If both bits are 1, then the
   result becomes 1. If either bit of the IP address OR subnet mask are
   0, then the result is 0. In the result below, where there are 1
   values, you can see that the IP address and subnet mask both have 1
   for that particular bit. Otherwise, the result for that bit is 0.

To verify that this is the problem, the user can perform the AND-ing operation using the following steps:

   NOTE: Windows NT Calculator, in scientific mode, can be used to convert
   decimal values to binary equivalent. Each binary octet should consist
   of eight (8) characters, if the calculator returns a value with only
   seven (7) or fewer characters, then append the appropriate number of
   zeroes (0) to the beginning of each octet so that all octets consist of
   eight (8) characters.

  • Convert each octet of the Start Address to binary (in our case, it is only the last octet that is different, so we only need to convert the last octet, but for the purposes of this article, all four octets are converted).

    This example: 205.241.139.160 = 11001101.11110001.10001011.10100000

  • Convert each octet of the End Address to binary.

    This example: 205.241.139.223 = 11001101.11110001.10001011.11011111

  • Convert each octet of the Subnet Mask to binary.

    This example: 255.255.255.160 = 11111111.11111111.11111111.10100000

  • Perform an AND against the Start Address and the Subnet Mask.

    Start Address: 11001101.11110001.10001011.10100000

       Subnet Mask:    11111111.11111111.11111111.10100000
       --------------  -----------------------------------
       Result #1:      11001101.11110001.10001011.10100000
    
    

  • Perform an AND against the End Address and the Subnet Mask.

    Start Address: 11001101.11110001.10001011.10100000

       Subnet Mask:    11111111.11111111.11111111.11011111
       --------------  -----------------------------------
       Result #2:      11001101.11110001.10001011.10000000
    
    

  • Compare Result #1 and Result #2 - if they do not match, the scope overlaps a sub network.

       Result #1:      11001101.11110001.10001011.10100000
       Result #2:      11001101.11110001.10001011.10000000
       --------------  -----------------------------------
                       same    .same    .same    .different --> different
                                                                 subnets
    
    
    This error message will also be displayed if you attempt to create a scope that has a beginning address that is the same as your network ID (scope ID).

    RESOLUTION

    In the above example, the ISP provided a range of 64 addresses without indicating that it was a range of addresses for two (2) sub-networks, consisting of 32 addresses for each subnet. All you did then, was to divide the range in two, resulting in the following two scopes:

       This example: Scope #1:
                     Start Address - 205.241.139.160
                     End Address   - 205.241.139.191
                     Subnet Mask   - 255.255.255.160
    
                     Scope #2:
                     Start Address - 205.241.139.192
                     End Address   - 205.241.139.223
                     Subnet Mask   - 255.255.255.160
    
    
    If you calculated the subnets for the DHCP scope, type in a scope (Starting and Ending Addresses) for each subnet you calculated, individually. If the subnets were provided by a third party (such as an ISP), ask them to provide a list of how the subnets are divided, including the ranges of host IDs within each subnet. Use this list to create your DHCP scopes.

       NOTE: Versions of Windows NT DHCP server prior to Windows NT 4.0
       Service Pack 2 (SP2) are not capable of assigning addresses from more
       than one scope to a given physical subnet. One workaround for this
       situation is to add additional network interface cards (NICs) to the
       server, and to address each of the NICs to a given logical IP subnet.
       This involves additional and otherwise unnecessary hardware, so a new
       solution was developed and implemented in Windows NT 4.0 SP2. The
       enhanced DHCP server allows the administrator to create different
       scopes (ranges of IP addresses), and then to group those scopes
       together into a superscope. The procedure to create superscopes is
       described in the following Microsoft Knowledge Base article:
    
          ARTICLE-ID: Q161571
          TITLE     : Using DHCP "Superscopes" to Serve Multiple Logical
                      Subnets
    
    Keywords          : kbhowto NTSrv nttcp ntui kbenv kberrmsg kbnetwork
    Version           : WinNT:3.5,3.51,4.0
    Platform          : winnt
    Issue type        : kbprb
    Solution Type     : kbworkaround

  • ================================================================================


    THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

    Last reviewed: January 13, 1998
    © 1998 Microsoft Corporation. All rights reserved. Terms of Use.