Word 97 RTF for Drawing Objects (Shapes)

1Wrap around top and bottom of shape (no text allowed beside shape)

2Wrap around shape

3None (wrap as if shape isn’t present)

4Wrap tightly around shape

5Wrap text through shape

0Wrap both sides of shape

1Wrap left side only

2Wrap right side only

3Wrap only on largest side

0Text is below shape

1Shape is below text

{ \shptxt  Any Valid RTF for the current textbox }

Note For linked text boxes, the first text box of the linked set has the entire story, so all following text boxes will not have a \shptxt field.

Inside of a \shpgrp, no { \shprslt .... } fields would be generated (that is, only the root-level shape can have a \shprslt field (this field describes the entire group). For example:

{ \shpgrp  ....... { \shp ..... (and all sub-items as usual) }
           { \shp ......(and all sub-items as usual) }

Note A { \shpgrp ...... } can be substituted for a { \shp ..... } at any place (to accomplish groups inside of groups).

0Square

1Tight

2None

3Top Bottom

4Through

0Top

1Middle

2Bottom

3Top Centered

4Middle Centered

5Bottom Centered

6Bottom Centered Baseline

0Horizontal non-ASCII font

1Top to bottom ASCII font

2Bottom to top non-ASCII font

3Top to bottom non-ASCII font

4Horizontal ASCII font

0Stretch each line of text to fit width

1Center text on width

2Left justify

3Right justify

4Spread letters out to fit width

5Spread words out to fit width

False if these properties are ignored.

0No links (default)

10Link to file; save with document

14Link to file; do not save picture with document

0A solid color

1A pattern (bitmap)

2A texture (pattern with its own color map)

3A picture centered in the shape

4Shade from start to end points

5Shade from bounding rectangle to end point

6Shade from shape outline to end point

7Shade using the fillAngle

0No links (default)

10Link to file; save with document

14Link to file; do not save picture with document

FillOriginY

FillShapeOriginX

fillShapeOriginY

allow an arbitrary position in the texture (relative to the top-left proportion of the texture's height and width) to be aligned on an arbitrary position on the shape (relative to the top-left proportion of the width and height of the bounding box).

Note that all these values are fixed point fractions of the relevant width or height.

0Solid fill with the line color

1Patterned fill with the lineFillBlip

2Textured fill with the lineFillBlip

3Picture fill with the lineFillBlip

0No links (default)

10Link to file; save with document

14Link to file; do not save picture with document

0Single line (of width lineWidth)

1Double lines of equal width

2Double lines, one thick, one thin

3Double lines, reverse order

4Three lines, thin, thick, thin

0Solid

1Dash (Windows)

2Dot (Windows)

3Dash dot (Windows)

4Dash dot dot (Windows)

6Dot

7Dash

8Long dash

9Dash dot

10Long dash dot

11Long dash dot dot

0Nothing

1Arrow

2Stealth arrow

3Diamond

4Oval

6Open arrow

7Chevron arrow

8Double chevron arrow

0Narrow

1Medium

2Wide

0Short

1Medium

2Long

0Offset shadow

1Double offset shadow

2Rich perspective shadow (cast relative to shape)

3Rich perspective shadow (cast in shape space)

4Perspective shadow cast in drawing space

6Emboss or engrave

If fc3DconstrainRotation (a Boolean property which defaults to True) is True the rotation is restricted to x-y rotation and the final rotation results from first rotating by c3DYRotationAngle degrees about the y-axis and then by c3DXRotationAngle degrees about the z-axis.

If fc3DconstrainRotation is False, the final rotation results from a single rotation of c3DrotationAngle about the axis specified by c3DrotationAxisX, c3DrotationAxisY, and c3DrotationAxisZ.

The X and Y values are a 16.16 fraction of the geometry width and height, with (0,0) being at the center of the geometry. The Z value must be in absolute units (EMUs).

If fC3DRotationCenterAuto is True the rotation will be about the center of the 3-D bounding cube of the 3-D group; otherwise, the rotation center will be about c3DRotationCenterX, c3DRotationCenterY, and c3DRotationCenterZ.

The X values and Y values are a fraction of the geometry width and height, with (0,0) being at the center of the geometry. The Z value is in absolute units.

1Render as a wire frame

2Render a bounding cube

These values are 16.16 numbers that specify the position of the origin within the shape bounding box as multiples of the width and height of that bounding box and relative to the center (that is, they are displaced from the center). When these values are applied, the actual transformed shape path is used rather than the shape geometry (compare with the shadow and perspective values which necessarily work on the geometry bounding box not the actual points). This means that a shape that extends outside the geometry bounding box (such as a text effect) is handled "correctly" for the calculation of the 3-D origin.

1Right angle

2One segment

3Two segments

4Three segments

1Any angle

230 degrees

343 degrees

460 degrees

590 degrees

0Top

1Center

2Bottom

3Specified by dxyCalloutDropSpecified