RAS_PORT_STATISTICS [New

RAS_PORT_STATISTICS

[New - Windows NT]

The RAS_PORT_STATISTICS structure reports the statistics that a RAS server collects for a connected port. The RAS server resets the various statistic counters each time the port is connected. You can call the RasAdminPortClearStatistics function to force the RAS server to reset the statistic counters.

For a port that is part of a multilink connection, this structure provides two sets of statistics. The first set contains the cumulative statistics for all ports in the connection. These statistics are the same for all ports in the connection. The second set contains the statistics for just this port. If the port is not part of a multilink connection, both sets of statistics have the same information. To determine whether a port is part of a multilink connection, check the PORT_MULTILINKED bit in the Flags member of the port's RAS_PORT_0 structure.

typedef struct _RAS_PORT_STATISTICS

{

// The connection statistics are followed by port statistics

// A connection is across multiple ports.

DWORD dwBytesXmited;

DWORD dwBytesRcved;

DWORD dwFramesXmited;

DWORD dwFramesRcved;

DWORD dwCrcErr;

DWORD dwTimeoutErr;

DWORD dwAlignmentErr;

DWORD dwHardwareOverrunErr;

DWORD dwFramingErr;

DWORD dwBufferOverrunErr;

DWORD dwBytesXmitedUncompressed;

DWORD dwBytesRcvedUncompressed;

DWORD dwBytesXmitedCompressed;

DWORD dwBytesRcvedCompressed;

// the following are the port statistics

DWORD dwPortBytesXmited;

DWORD dwPortBytesRcved;

DWORD dwPortFramesXmited;

DWORD dwPortFramesRcved;

DWORD dwPortCrcErr;

DWORD dwPortTimeoutErr;

DWORD dwPortAlignmentErr;

DWORD dwPortHardwareOverrunErr;

DWORD dwPortFramingErr;

DWORD dwPortBufferOverrunErr;

DWORD dwPortBytesXmitedUncompressed;

DWORD dwPortBytesRcvedUncompressed;

DWORD dwPortBytesXmitedCompressed;

DWORD dwPortBytesRcvedCompressed;

} RAS_PORT_STATISTICS, *PRAS_PORT_STATISTICS;

Members

dwBytesXmited

Specifies the total number of bytes transmitted by the connection.

dwBytesRcved

Specifies the total number of bytes received by the connection.

dwFramesXmited

Specifies the total number of frames transmitted by the connection.

dwFramesRcved

Specifies the total number of frames received by the connection.

dwCrcErr

Specifies the total number of CRC errors on the connection. CRC errors are caused by the failure of a cyclic redundancy check. A CRC error indicates that one or more characters in the data packet received were found garbled on arrival.

dwTimeoutErr

Specifies the total number of time-out errors on the connection. Time-out errors occur when an expected character is not received in time. When this occurs, the software assumes that the data has been lost and requests that it be resent.

dwAlignmentErr

Specifies the total number of alignment errors on the connection. Alignment errors occur when a character received is not the one expected. This usually happens when a character is lost or when a time-out error occurs.

dwHardwareOverrunErr

Specifies the total number of hardware overrun errors on the connection. These errors indicate the number of times the sending computer has transmitted characters faster than the receiving computer hardware can process them. If this problem persists, reduce the BPS connection rate on the client.

dwFramingErr

Specifies the total number of framing errors on the connection. A framing error occurs when an asynchronous character is received with an invalid start or stop bit.

dwBufferOverrunErr

Specifies the total number of buffer overrun errors on the connection. A buffer overrun error occurs when the sending computer is transmitting characters faster than the receiving computer can accommodate them. If this problem persists, reduce the BPS connection rate on the client.

dwBytesXmitedUncompressed

Specifies the total number of bytes transmitted uncompressed by the connection.

dwBytesRcvedUncompressed

Specifies the total number of bytes received uncompressed by the connection.

dwBytesXmitedCompressed

Specifies the total number of bytes transmitted compressed by the connection.

dwBytesRcvedCompressed

Specifies the total number of bytes received compressed by the connection.

dwPortBytesXmited

Specifies the total number of bytes transmitted by the port.

dwPortBytesRcved

Specifies the total number of bytes received by the port.

dwPortFramesXmited

Specifies the total number of frames transmitted by the port.

dwPortFramesRcved

Specifies the total number of frames received by the port.

dwPortCrcErr

Specifies the total number of CRC errors on the port. CRC errors are caused by the failure of a cyclic redundancy check. A CRC error indicates that one or more characters in the data packet received were found garbled on arrival.

dwPortTimeoutErr

Specifies the total number of time-out errors on the port. Time-out errors occur when an expected character is not received in time. When this occurs, the software assumes that the data has been lost and requests that it be resent.

dwPortAlignmentErr

Specifies the total number of alignment errors on the port. Alignment errors occur when a character received is not the one expected. This usually happens when a character is lost or when a time-out error occurs.

dwPortHardwareOverrunErr

Specifies the total number of hardware overrun errors on the port. These errors indicate the number of times the sending computer has transmitted characters faster than the receiving computer hardware can process them. If this problem persists, reduce the BPS connection rate on the client.

dwPortFramingErr

Specifies the total number of framing errors on the port. A framing error occurs when an asynchronous character is received with an invalid start or stop bit.

dwPortBufferOverrunErr

Specifies the total number of buffer overrun errors on the port. A buffer overrun error occurs when the sending computer is transmitting characters faster than the receiving computer can accommodate them. If this problem persists, reduce the BPS connection rate on the client.

dwPortBytesXmitedUncompressed

Specifies the total number of bytes transmitted uncompressed by the port. If the port is part of a multilink connection, this member is not valid. Use the compression statistics for the connection instead.

dwPortBytesRcvedUncompressed

Specifies the total number of bytes received uncompressed by the port. If the port is part of a multilink connection, this member is not valid. Use the compression statistics for the connection instead.

dwPortBytesXmitedCompressed

Specifies the total number of bytes transmitted compressed by the port. If the port is part of a multilink connection, this member is not valid. Use the compression statistics for the connection instead.

dwPortBytesRcvedCompressed

Specifies the total number of bytes received compressed by the port. If the port is part of a multilink connection, this member is not valid. Use the compression statistics for the connection instead.