A configuration command that modifies the call control parameters related to UTRAN system messages of a cell. In this command, the following parameters uniquely identify the cell:
Cell Index or Cell Name
| ID | Name | Description |
|---|---|---|
| IDXTYPE | Index type | Meaning:Index type Value range:BYNAME(By Name),BYIDX(By Index) Explanation:Index Type. Default value:None |
| CELLIDX | Cell index | Meaning:Cell index Value range:0~2047 Explanation: This parameter indicates the source cell index. The source cell index must be unique. Default value:None |
| CELLNAME | Cell name | Meaning:Cell name Value range:1-32 characters Explanation: This parameter indicates the name of the source cell. The name of each cell under one BSC must be unique. Default value:None |
| MSCVER | MSC Version indication | Meaning:MSC Version indication Value range:R98_or_below(R98 or below),R99_or_above(R99 or above) Explanation: This parameter indicates the protocol version of the MSC that works with the BSC. The supported signaling varies with the protocol versions. Default value:None |
| MEASURETYPE | Measurement Report Type | Meaning:Measurement Report Type Value range:EnhMeasReport(Enhanced Measurement Report),ComMeasReport(Common Measurement Report) Explanation: This parameter specifies the type of measurement report sent by an MS. The enhanced measurement report is a new downlink measurement report, reported by the MS. Compared with the normal measurement report, the enhanced measurement report has some new measurement items, such as BER and FER. An MS can report up to six GSM neighbor cells in a normal measurement report. Compared with the normal measurement report, the enhanced measurement report has more measurement items. Default value:None |
| GSMFREQCNUM | Serving band reporting | Meaning:Serving band reporting Value range:0~3 Explanation: If the system information indicates "MBR", the MS reports the number of neighbor cells on different frequency bands. When the MS reports the number of neighbor cells on the same frequency band with the serving cell, a maximum of the value of Serving Band Reporting can be reported. These neighbor cells must meet the following requirements: 1. The receive levels of the neighbor cells must be higher than 900 Reporting Threshold or 1800 Reporting Threshold. 2. The BSIC of a neighbor cell must be valid. 3. The signals of the neighbor cells must be the strongest among all the neighbor cells on the same frequency band. Default value:None |
| QI | Qsearch I | Meaning:Qsearch I Value range:0~15 Explanation: This parameter specifies the level threshold for cell reselection in idle mode. In idle mode, if the signal level in the serving cell is below [0, 7] or above [8, 15], the MS starts to search for 3G cells. For example: If this parameter is set to 5 and if the signal level of the serving cell is lower than 5, the MS starts to search for 3G cells. If this parameter is set to 10 and if the signal level of the serving cell is higher than 10, the MS starts to search for 3G cells. 0: -98 dBm 1: -94 dBm 2: -90 dBm 3: -86 dBm 4: -82 dBm 5: -78 dBm 6: -74 dBm 7: (always), that is, the MS keeps searching for 3G cells 8: -78 dBm 9: -74 dBm 10: -70 dBm 11: -66 dBm 12: -62 dBm 13: -58 dBm 14: -54 dBm 15: infinity(never), that is, the MS does not search for 3G cells. Default value:None |
| QCI | Qsearch C initial | Meaning:Qsearch C initial Value range:Use_Qsearch_I(Use Qsearch_I),Always(Always) Explanation: This parameter specifies the threshold of the signal level for cell reselection in connection mode before Qsearch C is obtained. Default value:None |
| FDDQOFF | FDD Q offset | Meaning:FDD Q offset Value range:0~15 Explanation: Only when the average receive level of a 3G cell is FDD Q Offset greater than that of the serving cell, the 3G cell becomes a candidate cell. 0: negative infinity(always select a cell if acceptable) 1: -28 dB 2: -24 dB ... 15: 28 dB. Default value:None |
| FDDREP | FDD REP QUANT | Meaning:FDD REP QUANT Value range:RSCP(RSCP),EcN0(Ec/N0) Explanation: This parameter specifies the measurement report counter of an FDD cell. Default value:None |
| FDDFREQCNUM | FDD MULTIRAT reporting | Meaning:FDD MULTIRAT reporting Value range:0~3 Explanation: This parameter specifies the number of UTRAN FDD cells that should be contained in the best cell list or in the measurement report. Default value:None |
| FDDQMIN | FDD Qmin | Meaning:FDD Qmin Value range:0~7 Explanation: This parameter specifies one threshold of the signal level for 3G cell reselection. Only when the receive level of a 3G cell is greater than FDD Qmin, the 3G cell can be one candidate cell for cell reselection. 0: -20 dB 1: -6 dB 2: -18 dB 3: -8 dB 4: -16 dB 5: -10 dB 6: -14 dB 7: -12 dB. Default value:None |
| QP | Qsearch P | Meaning:Qsearch P Value range:0~15 Explanation: This parameter specifies one threshold of the signal level for cell reselection in packet transfer mode. In packet transfer mode, if the signal level in the serving cell is below [0, 7] or above [8, 15], the MS starts to search for 3G cells. For example: If this parameter is set to 5 and if the signal level of the serving cell is lower than 5, the MS starts to search for 3G cells. If this parameter is set to 10 and if the signal level of the serving cell is higher than 10, the MS starts to search for 3G cells. 0: -98 dBm 1: -94 dBm ... 6: -74 dBm 7: (always) 8: -78 dBm 9: -74 dBm ... 14: -54 dBm 15: infinity (never). Default value:None |
| 3GSEARCH | 3G Search PRIO | Meaning:3G Search PRIO Value range:NO(NO),YES(YES) Explanation: This parameter specifies whether the MS is allowed to search for a 3G cell when the BSIC must be decoded. Default value:None |
| INVALBSICEN | Invalid BSIC reporting | Meaning:Invalid BSIC reporting Value range:NO(NO),YES(YES) Explanation: This parameter specifies whether the EMR can contain the information about a cell with an invalid BSIC. Default value:None |
| SCALEORDER | SCALE_ORDER | Meaning:SCALE_ORDER Value range:ADD0dB(+0dB),ADD10dB(+10dB),Automatic(Automatic) Explanation: This parameter indicates that when the MS reports the EMR, it adds the value of this parameter to the received signal level, and then converts the result into the RXLEV value. For details, see GSM Rec. 05.08. If the SCALE_Order reported by the MS is 10 dBm, level values 0-63 map with -100 dBm to -37 dBm. If the SCALE_Order reported by the MS is 0 dBm, level values 0-63 map with -110 dBm to -47 dBm. If the SCALE_Order reported by the MS is Automatic, the MS chooses the least SCALE while ensuring that the MS can report the most strong level. Default value:None |
| QSEARCHC | Qsearch C | Meaning:Qsearch C Value range:0~15 Explanation: This parameter specifies the level threshold for cell reselection in connection mode. In connection mode, if the signal level in the serving cell is below [0, 7] or above [8, 15], the MS starts to search for 3G cells. For example: If this parameter is set to 5 and if the signal level of the serving cell is lower than 5, the MS starts to search for 3G cells. If this parameter is set to 10 and if the signal level of the serving cell is higher than 10, the MS starts to search for 3G cells. 0: -98 dBm 1: -94 dBm ... 6: -74 dBm 7: (always) 8: -78 dBm 9: -74 dBm ... 14: -54 dBm 15: infinity (never). Default value:None |
| CELL900OFF | 900 reporting offset | Meaning:900 reporting offset Value range:0~7 Explanation: This parameter specifies the signal level offset of a GSM900 cell. When the priority of a GSM900 cell is sequenced on the basis of its frequency band, the value of this parameter should be added to the receive level in the measurement report. 0: 0 dB 1: 6 dB ... 7: 42 dB. Default value:None |
| CELL900THRED | 900 reporting threshold | Meaning:900 reporting threshold Value range:0~7 Explanation: This parameter specifies the threshold for determining whether the MR about a GSM900 cell is valid. When the receive level of the GSM900 cell in the measurement report is greater than the value of this parameter, the measurement report is valid. After the measurement report is filtered, the cell joins in the cell priority rank. 0: 0 dB 1: 6 dB ... 6: 36 dB 7: infinity. Default value:None |
| CELL1800OFF | 1800 reporting offset | Meaning:1800 reporting offset Value range:0~7 Explanation: This parameter specifies the signal level offset of a DCS1800 cell. When sequencing the priority of a DCS1800 cell based on its frequency band, the value of this parameter should be added to the receive level in the measurement report. 0: 0 dB 1: 6 dB ... 7: 42 dB. Default value:None |
| CELL1800THRED | 1800 reporting threshold | Meaning:1800 reporting threshold Value range:0~7 Explanation: This parameter specifies the threshold for determining whether the MR about a DCS1800 cell is valid. If the receive level of the 1800 MHz cell in the measurement report is greater than the value of this parameter, the measurement report is valid. After the measurement report is filtered, the cell joins in the cell priority sequence. 0: 0 dB 1: 6 dB ... 6: 36 dB 7: infinity. Default value:None |
| FDDCELLOFF | FDD reporting offset | Meaning:FDD reporting offset Value range:0~7 Explanation: This parameter specifies the signal level offset of an FDD cell. When the priority of a 3G cell is sequenced, it is recommended that the value of this parameter be added to the receive level of the 3G cell in the measurement report. 0: 0 dB 1: 6 dB ... 7: 42 dB. Default value:None |
| FDDCELLTHRED | FDD reporting threshold | Meaning:FDD reporting threshold Value range:0~7 Explanation: This parameter specifies the threshold for determining whether the MR about an FDD cell is valid. If the receive level of the 3G cell in the measurement report is greater than the value of this parameter, the measurement report is valid. After the valid measurement report is filtered, the 3G cell joins in the cell priority sequence. 0: 0 dB 1: 6 dB ... 6: 36 dB 7: infinity. Default value:None |
| TDDCELLRESELDIV | TDD cell reselect diversity[db] | Meaning:TDD cell reselect diversity[db] Value range:0~15 Explanation:A TDD cell can become a candidate cell only when the average receive level of the TDD cell is greater than the TDD Cell Reselect Diversity of the serving cell. 0: negative infinity (always select a cell if acceptable) 1: -28 dB 2: -24 dB ... 15: 28 dB. Default value:None |
| BESTTDDCELLNUM | Best tdd cell number | Meaning:Best tdd cell number Value range:0~3 Explanation:This parameter specifies the number of UTRAN TDD cells that should be contained in the best cell list or in the measurement report. Default value:None |
| TDDCELLOFF | TDD reporting offset | Meaning:TDD reporting offset Value range:0~7 Explanation:This parameter specifies the signal level offset of a TDD cell. Add the value of this parameter to the receive level of the TDD cell in the measurement report, and then sequence the TDD cells. 0: 0 dB 1: 6 dB ... 7: 42 dB. Default value:None |
| TDDCELLTHRED | TDD reporting threshold | Meaning:TDD reporting threshold Value range:0~7 Explanation:This parameter specifies the threshold for determining whether the MR about a TDD cell is valid. The measurement report is valid if the receive level of the TDD cell in the measurement report is greater than the value of this parameter. After the valid measurement report is filtered, the TDD cell joins in the cell prioritization. 0: 0 dB 1: 6 dB ... 6: 36 dB 7: infinity. Default value:None |
| TDDSIOPTIMIZEDALLOWED | TDD System Information Optimized Allowed | Meaning:TDD System Information Optimized Allowed Value range:NO(NO),YES(YES) Explanation: This parameter specifies whether to optimize the system information 2Quater and MI of the TDD neighboring cell. That is, to add an FDD neighboring cell information before the TDD neighboring cell information to solve the compatibility problem of some dual-mode MSs. Default value:None |
| TDDMIPROHIBIT | TDD MI System Information Broadcasting Prohibit | Meaning:TDD MI System Information Broadcasting Prohibit Value range:NO(NO),YES(YES) Explanation: This parameter specifies whether to send the system information MI which contains the 3G neighboring cell information in the TDD neighboring cell. The value YES(YES) indicates that the MI is sent, and the value NO(NO) indicates that the MI is not sent. Default value:None |
Modify the call control parameters related to UTRAN system messages of a cell (Index Type = BYIDX(By Index); Cell Index = 0): MOD CELLCCUTRANSYS: IDXTYPE=BYIDX, CELLIDX=0, MSCVER=R99_or_above, MEASURETYPE=EnhMeasReport, GSMFREQCNUM=2, QI=10, QCI=Always, FDDQOFF=10, FDDREP=EcN0, FDDFREQCNUM=2, FDDQMIN=4, QP=14, 3GSEARCH=YES, INVALBSICEN=YES, SCALEORDER=ADD10dB, QSEARCHC=10;