Adding a BTS (GSM/UMTS)

This describes the GSM initial configuration of the DBS3900 GSM/UMTS for the BSC, which includes configurations of BTS attributes, logical TRXs, and cell attributes.

Prerequisites

• The data described in Data to Be Negotiated and Planned for DBS3900 Initial Configuration is already obtained.
• The BSC global data, BSC devices, BSC links, and BSC clock are configured.
• The GFGUB/GOGUB is configured. If a pair of active and standby GFGUBs/GOGUBs are configured, their device IP addresses and port IP addresses are configured.
• The GXPUM/GXPUT is configured for the GMPS or GEPS where the GFGUB/GOGUB is located.
• The GDPUX is configured for the GMPS or GEPS where the GFGUB/GOGUB is located.

NOTE:

• Abis interface boards are classified into the GEIUB, GOIUB, GEHUB, GFGUB, and GOGUB.
• The RF modules of the GSM/UMTS BTS are classified into MRRU and MRFU. When the DBS3900 is applied, the MRRU is configured. When the BTS3900 or BTS3900A is applied, the MRFU is configured.
• If the GSM/UMTS BTSs share the IP transmission resources, set the gateway IP address to the IP address on the UMTS side described in the configuration of BSC routes in Configuring the GFGUB/GOGUB.

Procedure

1. Obtain the negotiated and planned data of the GSM/UMTS base station and the data prepared for the RF channel allocator.
2. Allocate RF channels through the RF channel allocator.
3. Start the Add Site wizard on the BSC6000 Local Maintenance Terminal.

   If...	Then...
   A site is added for the first time,	Right-click the GFGUB/GOGUB interface board of the GMPS or GEPS, and then choose Add Site from the shortcut menu. A dialog box is displayed, as shown in Figure 1.
   A cascaded BTS is to be added under an existing BTS,	Right-click the existing BTS on the management tree, and then choose Site Operation > Add Site from the shortcut menu. A dialog box is displayed, as shown in Figure 1.

   Figure 1 Add Site dialog box (1)
   
   

4. Click Add Site. A dialog box is displayed, as shown in Figure 2. Then, set related parameters.
   Figure 2 Add New Site dialog box
   
   

5. Click OK. A dialog box is displayed, as shown in Figure 3.
   Figure 3 Add Site dialog box (2)
   
   

6. Click Next. A dialog box is displayed, as shown in Figure 4.
   Figure 4 Add Site dialog box (3)
   
   

7. Select the target BTS and click Add Cell. A dialog box is displayed, as shown in Figure 5. Then, set parameters in the displayed dialog box.
   Figure 5 Add New Cell dialog box
   
   
   CAUTION:

   If you find the configuration error of a frequency band in a cell or BTS after the configuration is complete, you need to delete the cell or BTS and then add a cell or BTS to modify the frequency band. The reason is that a frequency band cannot be modified in a configured cell or BTS.

8. Click OK. A dialog box is displayed, as shown in Figure 6.
   Figure 6 Add Site dialog box (4)
   
   

9. Click Next. A dialog box is displayed, as shown in Figure 7.
   Figure 7 Add Site dialog box (5)
   
   

10. Click Site Attributes. A dialog box is displayed, as shown in Figure 8.
    Figure 8 Site Device Attributes dialog box (1)
    
    

11. In the Site Device Attributes dialog box, right-click the GTMU and choose Configure Board Attributes from the shortcut menu. A dialog box is displayed. Click the FE port parameters of BTS tab on the Basic Attributes of Site Board dialog box, as shown in Figure 9. Then, set related parameters.
    Figure 9 FE Port Parameter of BTS tab page
    
    
    NOTE:

    BTS3012, BTS3012AE, BTS3012_II, DBS3900, BTS3900, BTS3900A, BTS3900B, and BTS3900E do not support that Muplex Mode is set to HALF.

    The parameter Peer Port IP address index specifies the index of the valid IP address for a BSC port. The BSC supports the settings of multiple IP addresses under one Port No.. Peer Port IP address index maps the valid IP address of the BSC port. After the value of Peer Port IP address index is specified, the BSC IP Address in the IP Interface Board Parameter of BTS tab page is generated automatically and cannot be changed.

12. Click the IP Interface Board Parameter of BTS tab to display the tab page, as shown in Figure 10. Then, set related parameters.
    NOTE:

    You can obtain the BTS Interface Board Bar Code by running the DSP BTSESN command.

    Figure 10 IP Interface Board Parameter of BTS tab page
    
    

13. Click OK to return to the Site Device Attributes dialog box.
14. In the Site Device Attributes dialog box, right-click and choose Add RXU Chain from the shortcut menu. A dialog box is displayed, as shown in Figure 11. Then set related parameters.
    Figure 11 Add RXU Chain dialog box
    
    
    NOTE:

    • Chain Head Board Port must be set to 3, 4, or 5. Among six CPRI ports on the GTMU, ports 3, 4, and 5 are used to connect the RF module; ports 0, 1, and 2 are used to connect the three CPRI ports on the WBBP.
    • Each GTMU supports a maximum of six RXU chains.
    • When star and chain topologies are applied for the BBU and the RF module, each chain supports three-level cascading of the RF module.
    • Chain No. is an identifier rather than the actual CPRI port number. The actual port number is specified by Chain Head Board Port.

15. Click OK. The RXU chain is added, as shown in Figure 12.
    Figure 12 Added RXU chain 1
    
    

16. Add the RF module. Right-click the RXU chain, and then choose Add RXU > Add MRRU. A dialog box is displayed, as shown in Figure 13. Then, set related parameters.
    Figure 13 Add MRRU dialog box
    
    
    NOTE:

    RXU NAME of different RF modules under the same BTS must be unique. Otherwise, the system may display error information.

17. Click OK. The RF module is added.
18. Right-click an RF module, and then choose Configure RXU Attribute from the shortcut menu. The Basic Attributes of Site Board dialog box is displayed.
19. In the dialog box, click the Configure Site Board Attributes dialog box, as shown in Figure 14.
    Figure 14 Configuring MRRU board attributes
    
    

20. Set Working Standard to GSM and UMTS, and set other parameters.

    Table 1 Description of setting board attributes of the BTS

    Parameter	Setting Description
    Send Receive Mode	Set this parameter according to the actual RF connections. For details, see Setting Antenna Attributes.
    Antenna Tributary 1 Tower-Top Amplifier Flag and Antenna Tributary 2 Tower-Top Amplifier Flag	Set this parameter according to the actual configuration of the antenna.
    Antenna Tributary 1 Tower-Top Amplifier Attenuation Factor(dB) and Antenna Tributary 2 Tower-Top Amplifier Attenuation Factor(dB)	Set this parameter to TMA Gain-4. Obtain information on the "TMA gain" from the product specifications.

21. Click OK to return to the Site Device Attributes dialog box.
22. Right-click an RF module, and then choose Bind Logical TRX from the shortcut menu. A dialog box is displayed, as shown in Figure 15. Then, set related parameters.
    Figure 15 Binding Logical TRX dialog box
    
    
    NOTE:

    • In single TX channel mode, the total number of carriers (number of GSM carriers + number of UMTS carriers) is less than or equal to six; the total number of UMTS carriers is less than or equal to two; the total number of GSM carriers is less than or equal to six.
    • In double TX channel mode, the carrier combination with non-transmit diversity that serves channels in different working modes should follow the following principles.
      • The total number of carriers on each channel is less than or equal to four.
      • The total number of UMTS carriers on each channel is less than or equal to two.
      • The total number of GSM and UMTS carriers on two channels is less than or equal to six.
    • Maximum total output power and number of TRXs
      • For single channel A, the maximum total output power is 40 W and number of serving carriers ranges from 0 to 6.
      • For channels A and B, the maximum total output power of each channel is 30 W, and number of serving carriers of each channel ranges from 1 to 4.

23. Click OK to return to the Site Device Attributes dialog box.
24. Repeat 16 through 23 to configure multiple RF modules and other logical TRXs.
    NOTE:

    For details about configuring the RXU chain and RF module in different cascading modes, see Adding the RXU Chain and RF Module (Star Topology), Adding the RXU Chain and RF Module (Chain Topology), or Adding the RXU Chain and RF Module (Ring Topology).

25. Repeat 14 through 23 to configure multiple RXU chains.
26. Add other modules to subrack 2 in the Site Device Attributes dialog box. For details, see Adding BTS Modules.
27. Right-click and choose Add SFP Switch Port from the shortcut menu. A dialog box is displayed, as shown in Figure 16. Then, set parameters. For details about the mapping between the logical port SFP in the software and the physical port CPRI on the GTMU, see Table 2.
    Figure 16 Add SFP Switch Port dialog box
    
    
    NOTE:

    • The GTMU provides the SFP switching port for the WBBP. The data transfer between the WBBP and the RF module is implemented through the configuration of the switching port.
    • SFP Port No specifies which port of the CPRI0, CPRI1, and CPRI2 of the GTMU connects to the CPRI port of the WBBP.
    • Switch Port specifies which port of the CPRI3, CPRI4, and CPRI5 of the GTMU connects the RF module.

    Table 2 Mapping between the SFP port and the CPRI port

    Physical Port on the GTMU	Logical Port	Connection Attributes	Switch Port	Description
    CPRI_0	SFP_0	BBU	3-5	Physical port specifies a CPRI port that connects to the WBBP. Logical port specifies a logical port that is bound to one of ports SFP_3, SFP_4, and SFP_5, thus achieving information exchange between the RF module and the WBBP.
    CPRI_1	SFP_1
    CPRI_2	SFP_2

28. Click OK, as shown in Figure 17.
    Figure 17 Site Device Attributes dialog box (4)
    
    

29. If the GSM network needs to provide E1/T1 transmission timeslots to or borrow them from the UMTS network, set TOP switch parameters. For details, see Configuring the TOP Switching Parameters of 3900 Series BTSs.
30. Click OK to return to the Add Site dialog box.
31. Click Next. A dialog box is displayed, as shown in Figure 18.
    Figure 18 Add Site dialog box (7)
    
    

32. Click Cell Attributes. A dialog box is displayed, as shown in Figure 19.
    Figure 19 Set Cell Attributes dialog box
    
    

33. Set parameters of basic cell attributes.
    NOTE:

    For two cells, the values of at least one of the following parameters should be different: MCC, MNC, LAC, and CI.

34. In the TRX Attributes group box, select the allocated TRXs, as shown in Figure 20.
    Figure 20 TRX Attributes group box
    
    

35. Click Frequency Config. A dialog box is displayed, as shown in Figure 21. Then, select a frequency.
    Figure 21 Set Cell Frequency dialog box
    
    
    NOTE:

    Frequency spacing between carriers of each channel is described as follows:

    • Frequency spacing between carriers in the UMTS network ranges from 4.2 MHz to 5 MHz.
    • Minimum frequency spacing between carriers in the GSM network is 200 KHz.
    • Frequency spacing between carriers in the GSM network and that in the UMTS network is 2.4 MHz.

    The setting of the frequency spacing that is less than 5 MHz is restricted by the license.

36. Click OK to return to the Set Cell Attributes dialog box.
37. Select the added cell, and then click Cell Attributes. A dialog box is displayed, as shown in Figure 22.
    Figure 22 Configure TRX Attributes dialog box
    
    

38. Add a frequency corresponding to the TRX from Available Frequencies to Assigned Frequencies.
39. Click the Channel Attributes tab. A tab page is displayed, as shown in Figure 23. Then, set the channel types corresponding to eight channel numbers.
    Figure 23 Channel Attributes tab page
    
    

40. Click the Device Attributes tab. A dialog box is displayed, as shown in Figure 24.
    Figure 24 Device Attributes tab page
    
    

41. Set Power Level, Power Type, Receive Mode, and Send Mode.

42. Click OK to return to the Set Cell Attributes dialog box.
43. Repeat 37 through 42 until the frequencies, channel attributes, and device attributes of all the TRXs in a cell are configured.
44. Click OK to return to the Add Site dialog box.
45. Repeat 32 through 44 until the attributes of all the cells are configured.
46. Click Finish. The configuration of the BTS is complete.
47. Activating a BTS.
    1. On the Management Tree tab page of the BSC6000 Local Maintenance Terminal, right-click the target BTS and choose Site Operation > Set Site Active State from the shortcut menu. A dialog box is displayed, as shown in Figure 25.
       Figure 25 Set Site Active State dialog box
       
       

    2. Under Site Active State, select Activated. Then, click Finish to complete the BTS activation.